UPVC Window Handle Replacement
It’s simple to repair a broken window handle using the appropriate tools. It is essential to know what kind of handle you have and the spindle’s size before you purchase an alternative.
Older uPVC windows have handles with cockspurs, which have an extension spur that can lock over a cockspur wedge striker plate. These can be left- or right-handed, and must match when replaced.
What type of lock or handle do you have? I have
There are a variety of windows locks and handles made of upvc each with their distinct advantages and functions. The type of handle you are using will determine how easy it is to open your windows and if the locking mechanism functions according to the plan. Over time and through regular use, upvc window handles can become damaged or worn out, UPVC Window Handle Replacement making them less secure and effective. In some instances, they may even be completely removed. If you notice that your upvc window handles have been removed, it’s essential to fix them as soon as possible. This will help prevent burglaries, and keep your house safe.
It’s an easy task that virtually anyone can perform. You’ll require a few basic tools, but with proper knowledge, it’s an easy task that will only take a couple of minutes. You must be aware of the type of lock or handle you have on your window. This will allow you to choose the appropriate glass replacement windows.
Inline Espagnolette Handles
They are usually found on the sides of the window. They have a flat design and have a latch that engages with the locking mechanism on the frame of the window when it is turned. Inline upvc handles feature an elongated spindle that runs through middle of the handle and into the window frame to control the latch.
Cockspur Handles
They are typically found on older uPVC window frames and feature distinct hook-shaped designs. Cockspur handles are held to the frame of the window with only one screw and are less secure than other kinds of window handle.
Tilt and Turn Handles
Unlike the other upvc handles that are tilt and turn, these handles can be turned to open the window and turned inwards to allow to allow ventilation. In general, they have a 7mm spindle at the back of the handle and are available in left and right-handed versions.
When purchasing replacement handles made of upvc it is essential to check the spindle length because not all handles are the same size. To test the length of your handle made of upvc, simply drop something in the middle of the hole, and then measure the distance it travels before it comes into contact with an obstruction. This is the longest spindle length that will be suitable for your window.
What is the spindle?
uPVC window handles work in a similar way to doors. By turning the handle, you can open a latch in the frame. This unlocks the window to allow it to be shut and opened. However, sometimes handles can be damaged, especially when they are used frequently or exposed to harsh weather conditions. This can lead to the need to replace your uPVC handles for windows as they may not operate the window correctly for a long time.
There are many different types of uPVC handles, including Espag, Cockspur, and Spaded handles. They are designed to fit inside the uPVC frames in various ways. Each handle uses a specific spindle to secure the mechanism into the window. It is important to identify the type of handle installed on your uPVC windows to ensure that you replace it with a suitable one.
You can check what type of uPVC handle you have by looking at the base section of the handle. There should be a’snap in cover over one screw that holds the handle’s base in place. Once you remove this you will be able to observe the second screw that holds the base of the handle in position. After both screws are removed you should be able to pull the handle away from the uPVC window.
Once you have removed your uPVC window handle you need to carefully remove the old spindle from the locking mechanism. Take note of the length of the spindle. You will need to buy a replacement of the same length as the original handle and locking device.
The spindle wears out and is unable to operate the locking mechanism. This could be due to damage from constant use or loosening of the locking mechanism, or even rust over time. When this happens it will be necessary to replace the window handle and the locking mechanism to restore full functionality to your uPVC windows.
How do I get rid of the handle that was previously attached?
Window handles can become damaged or broken over time. It is crucial to repair them as quickly a possible to ensure your safety. The good news is that replacing a damaged or worn handle is a relatively simple task that can be accomplished in less than an hour and doesn’t require any specialized tools.
To remove the old handle, you first need to remove the screw at the base of the handle. After the screw is removed, the handle can be removed. A second screw will be located at the bottom of the handle. This can also be removed. When both screws are removed the handle can be removed from the base of the window.
After removing the old handle and align the fixing holes of the new handle with the holes already present in the window frame. There might be a small cap or sticker on the new handle, so take off them if needed and then put the handle in place. Once the handle is set, it is crucial to verify that it is working by turning the handle and ensuring that the lock mechanism activates.
Espag handles come with spindles that extend out of the handle and slots into the multipoint locking mechanism that is on the frame of the window. Cadenza windows have a blade with cutouts which fit into the lock mechanism. Cockspur handles are long and hook over the frame of the window or the transom bar crossmember.
Once you have installed the new handle, slide the spindle inside the window lock and tighten it. Replace the snap-in cover and screw cap (if applicable) once the handle is securely fixed. The handle is now ready for use to use, so try opening and closing the window several times to make sure that it works properly and securely.
How do I fit the new handle?
The process of changing your window handle made of uPVC isn’t difficult, and the process is actually very simple. All you need is an screwdriver and a little bit of patience. First, make sure that the handle that you are replacing is unlocked. Then, remove any screws visible. You can also replace them with screw caps. After the handle has been removed, you need to make an note of the length of the spindle that protrudes from the back of the handle. This is crucial as it will determine the kind of handle you’ll need to purchase.
Espagnolette handles made of uPVC are the most well-known kind of handle. The spindle passes through the handle to operate the locking mechanism in the frame of the window. When the handle is turned it releases the latch on the window and allows it to open. When used regularly and over time, espagnolette handles may be damaged.
Cadenza handles are a kind of uPVC handle that is usually used with tilt and turn windows. They have a protruding knife that works with a multiple-point locking mechanism inside the window. They are usually more secure than espagnolette handles as they can only be opened from the inside. They can be replaced with the same method as espagnolette handles however you should make sure that the new handle has a curved blade as opposed to one that is flat.
After you have chosen the correct handle, simply align the new handle with the existing screw holes before screwing it in place. Then, put the screw covers back on and test that the new handle functions properly. This is done by shifting the handle from the locked to the unlocked position and the reverse direction several times. If you have any issues, it might be beneficial to speak with a professional to see if they can help resolve the problem. They can provide advice on how to solve the issue in a timely and efficient way.