Repairs to uPVC Windows
uPVC windows are an excellent option for modern homes. They are durable, long-lasting and easy to maintain. Unlike timber and aluminium, they don’t rust or rot.
Regularly cleaning and lubricating UPVC windows and doors is crucial. This will help avoid unnecessary repair costs as well as increase energy efficiency.
1. Broken Glass
If the glass in your window has been damaged, it could cause a large deal of damage to your home, which can make it very hazardous and possibly fatal. It is essential to ensure that your windows are in good shape.
Single-pane windows are relatively simple to replace, and they typically fit into frames of the past easily. However, if you have double pane windows that are secured by internal beading it will be more difficult to remove the existing panes and install new ones. In this instance it is essential to buy plastic spacers to aid in fitting the new pane into the window frame.
If you’re planning attempt to remove the glass panes yourself, it is essential to wear the proper safety gear such as gloves that are thick and protective eyewear. It is also recommended to lay down a drop cloth before you begin working on the window panes to ensure that any shards fall on the fabric, not onto the floor and could be trampled under.
It’s a great idea seal the gap after the glass has been removed. This will prevent water and drafts from entering your home until a professional comes out to fix the window. It also acts as a barrier that will prevent any intruders to gain access into your home. If the gap is particularly large, you might think about a security door that has an integrated window as it offers the best of both worlds.
2. Sagging
uPVC windows and doors are an affordable, durable and energy-efficient alternative to timber windows with sash. However, with time, they can suffer from a variety of problems including sliding. A sagging uPVC windows can cause issues with light, draughts and even security. It is crucial to act as soon as you notice your uPVC windows are falling down.
To fix a window that is sagging you can try repositioning the hinges. To do this, you’ll have to open the window to access the frame. You can then unscrew both the hinges on the top and bottom using a screwdriver and adjust them counter-clockwise or clockwise. Once you’ve adjusted the hinges, shut your window and verify the fit. If you’re satisfied with the fit, you can tighten the screws to ensure that they remain in the right place.
If you cannot reposition the hinges, you might have to replace the seal. Rubber seals may dry out and lose their elasticity over time, which causes them to loose their elasticity. If this happens, it’s essential to replace the seal as fast as possible so that your uPVC windows are waterproof and draught-proof.
uPVC handles may also become loose. This is often caused by screws that have loosened over time, but it could be due to the handle mechanism wears out. It’s relatively simple to fix a loose uPVC handle. First, upvc Repair you’ll need to shut the window and then perform a test fitting. The joint at the corner of the sash must align with the joint on the casing. If it doesn’t, you can use a screwdriver or a wrench to loosen the handle and then turn the mechanism back into its original position.
3. Water Leaks
If you wake up to wet floors and damp walls every time it rains it’s important to take action. Windows that leak water do can not only cause destruction of your home’s structure but also undermine your efforts to regulate the temperature in your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.
This is an easy fix that can be completed by anyone who is a DIYer with the skills. Depending on how serious the issue is, old caulking may have to be removed. When it comes to uPVC repair, you should avoid ‘over-caulking’. This will make your window more difficult to clean and reduce its energy efficiency.
Make sure that the drainage holes do not have debris inside them and ensure that the sill pan is properly angled to drain away from the window doctor near me. In more serious cases you might have to consider replacing the window.
Mold spots and rotted sills are other signs of water leakage. This fungus thrives under humid conditions and can propagate quickly throughout the home.
If the leakage occurs between the double-glazed glass it is more likely that the problem is with the seal than the frame. A uPVC specialist can easily fix this problem by replacing the glass seal. This will restore the full insulation of your windows.
4. Faulty Hinges
If your uPVC windows are brittle to open, or are loose and blow open in a breeze, it may be hinges that are at the fault. They can be easily repaired by any DIYer who is skilled and can usually be done within a few minutes.
Nearly every home in the UK will have top-hung or side-hung uPVC windows that have hinges and, just like any mechanical component they can wear down over time. It is essentially a very simple process but it can be simpler if you have someone to assist in holding the frame up.
It is also important to verify that the uPVC hinges are being opened and closed in the right direction. You can do this by looking for the arrow on each hinge, this indicates which way the window should be opened.
The issue can be caused due to opening the window in the wrong way or due to a poor installation in the factory. This can often be resolved by sending us a photograph on our website. We will be more than happy to give you advice.
It is also important to grease the hinges regularly. Applying a light engineering lubricant to the hinges is an ideal method to accomplish this. We recommend using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It also decreases the chance of windows getting stuck and stop corrosion. It is recommended to do this once a year. WD40 and other solvent-based oils are not recommended because they can damage the parts of your uPVC window.
5. Draughts
Draughts in windows made of upvc can be caused by a few different things. The hinges can also become disaligned as a result of wear, causing a gap where the sash and frame meet. These can be easily repaired by giving them a thorough clean, however when they’re beyond repair, it might be necessary to have them realigned or replaced. Second, the interlock can be disaligned. This is located on the hinge’s side, and may need to be cleaned. In some cases, it may be necessary to replace the hinges.
The next most common reason for draughts is window seals. These are susceptible to being worn out or damaged over time, and allow air to escape through these gaps. Installing high-quality weatherstripping is a good way to keep draughts at bay. Replace the windows made of upvc with low-emissivity glasses. This will help control indoor temperatures and lessen the possibility of draughts.
One of the most effective methods to reduce draughts is by using a draught excluder. These are usually fabric tubes that are filled with some type of filler. They can be put on the windowsill on top. They can keep your home warm by blocking cold air.
The windows made of upvc can continue to provide excellent insulation and security in your home by performing regular maintenance and repairs. It is essential to remember that all windows eventually get worn out and it could be more cost-effective to simply replace them rather than repair them. If you have any problems with your window made of upvc you should consult a professional immediately.