peugeot replacement key 208 Key Replacement
Peugeot 208 key replacement is best left to experienced auto locksmiths who have the right equipment and know-how. They will be able to make and program new keys much quicker than a dealership and at a lower cost.
A dead battery for your coin is most likely to blame the reason your key-fob stops locking or unlocking doors. There are other reasons that the key may be malfunctioning.
Dead Coin Battery
A dead battery can stop your peugeot 206 key programming 208 from locking and unlocking, as well as stopping it from starting the engine. In this situation you’ll need choose the alternate method to start found in your vehicle’s owner’s manual.
Another reason why your 208 might not be starting is that the spark plugs are worn down. The spark plugs are responsible for sparking the fuel that ignites the engine. They have a limited lifespan. If they’re not used enough to last, they’ll eventually fail.
There is an easy solution to this problem. Check the voltage of your battery using a multimeter. If the voltage falls below 11,5 volts, it’s time to replace it. It is also important to clean the battery’s contacts if it has corrosion. This can be done by removing the rubber covers off the two battery terminals, and then using a wirebrush to clean any corroded parts of the battery. It is then time to reconnect the cables to the positive and negative poles.
Water Damage
If your 208 won’t start and the battery isn’t empty, you must ensure whether the spark plugs are in good working order. It could be that they are just overly filthy, making them unable to spark. The spark plugs can be cleaned in the workshop.
Peugeot cars are equipped with a transponder key that is compatible with the car’s immobiliser system. This ensures that only a valid key is able to turn the engine. If the chip inside the Peugeot key is damaged then it will not send the proper signal to the vehicle.
This is a frequent issue that can occur due to water damage. This is most common in colder climates. the vehicle could have been exposed to snow or rain. If this is the case, seek out a reputable auto locksmith who has all the tools and equipment needed to reprogram the new key. They also have the most up-to-date technological know-how and machinery required to create a Peugeot 208 smart key. The process shouldn’t take longer than 15 minutes.
Contacts with the battery may be damaged.
Peugeot replaced the old transponder chips with a brand new type that uses electronic components that are mounted on a circuitboard. The new system is excellent when it’s brand new, but the circuit boards begin to degrade with time and cease to function properly.
This can stop the immobiliser from activating so your vehicle won’t be able to start. If this is the case it’s a good idea to get in touch with a Peugeot specialist or locksmith.
A common issue is when the battery of the key fob begins to die. This causes the blade of the key to stop feeding into the lock. A locksmith from your vehicle can replace the battery and cut a fresh blade for you, it’s generally a quick fix.
Faulty Receiver Module
If your Peugeot key fob was not working after dropping it on the floor, or being exposed to a sudden rain or accidently washing it, it could be due to a defective receiver module. The receiver is responsible for transmitting radio frequency signals to the on-board computer, which controls the central locking system of your Peugeot vehicle.
The rubber seals on the key fob keep water from getting to the electronic chip. The chip can be damaged by water when it is exposed to water for long periods of time. The high salt content of the ocean water or pool can cause damage to the key fob if it is submerged.
The module will need to be replaced if your Peugeot spare key is no longer working. This should be done by a Peugeot specialist or expert auto locksmith. Peugeot keys, unlike other cars, are secured by an immobilizer device. This requires the correct programming to allow the car to start. This is why you should choose a reputable Peugeot locksmith to take on the job of creating and programming the replacement.
Computers with faulty on-board computers
The computer on board of your Peugeot is responsible for many of the functions in your car including power windows and airbags. When something goes wrong with these systems, it will usually show a code that identifies the problem. The code is stored within the system and will remain there until the problem is resolved. This can often mean that the on-board computers to be replaced.
One of the main causes of the airbag light coming on is loose or corroded connectors in the airbag sensor. This can be caused by wear and tear, aging or exposure to salt and moisture. This issue should be dealt with as soon as you can, as an airbag that is malfunctioning could pose a risk in the event of an accident.
If you find an error message that says “card not found” on your Peugeot key fob, the battery inside the key fob might be weak or dead. This will stop the key fob from sending a signal to disarm the vehicle’s immobilizer. You can test this by pressing the unlock button on the key fob and then attempting to start your car. If it doesn’t work the battery on the key needs to be replaced.